Utax CD 1015 Servisní příručka Strana 70
- Strana / 296
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
1-4-22
2AV/X
Description
Maintenance
item No.
1-4
U099 Checking the original size detection
Description
Displays the original width detection data and sets the original width detection threshold.
Purpose
To check the original width detection. Also to change the original size detection threshold if the size of the
original on the contact glass is detected incorrectly.
Start
1. Press the start key. The screen for selecting an item is displayed.
2. Select the item.
3. Press the start key. The screen for executing is displayed.
Checking the original width detection data
Setting or checking the original width detection threshold
Display
DATA
B/W LEVEL
Description
Method to display the original width detection data
1. Place an original on the contact glass and turn the original detection switch on. The exposure lamp turns
on and the width of the original is detected. The scanner data taken at the nine points from (1) at the
machine rear to (9) at the machine front is displayed on the message display as follows.
The data is displayed within the range of 000 to 255, 000 indicating white (original present) and 255
indicating black (no original).
(1) (2) (3)
(4) (5) (6)
(7) (8) (9)
Figure 1-4-6
2. To return to the screen for selecting an item, press the stop/clear key.
Method to set or check the original size detection threshold
1. Place an original on the contact glass and turn the original detection switch on. The original size
detection starts and detection data is displayed.
* See Paper size in U073 for the paper size for each setting.
Display
Description
Data
range
Remarks
LEVEL
WAIT TIME
ORIGINAL AREA
SIZE
B_DATA
W_DATA
Scanner data threshold
Time between original detection switch turning on
and reading-in of scanner data
Detected original width
Original size detected by scanner data and original
size sensor detection data
Black (no original) data at the point on the boundary
between original area and no original area
White (original present) data at the point on the
boundary between original area and no original area
0 to 255
0 to 100 ms
0 to 350 mm
0 to 63*
0 to 255
0 to 255
Initial
setting
170
50
Adjustable
Adjustable
2. To change the original size detection threshold, select LEVEL or WAIT TIME using the cursor up/down
keys and change the setting using the cursor left/right keys.
3. Press the start key. The value is set.
4. To return to the screen for selecting an item, press the stop/clear key.
Completion
Press the stop/clear key at the screen for selecting an item. The screen for selecting a maintenance item
No. is displayed.
- UTAX CD 1015 / 1020 1
- Double-pole/neutral fusing 2
- 1. Installation Precautions 4
- 3. Miscellaneous 6
- CONTENTS 7
- 1-6 Assembly and Disassembly 9
- 2-1 Mechanical construction 10
- 2-2 Electrical Parts Layout 10
- 2-3 Operation of the PCBs 10
- 2-4 Appendixes 10
- 1-1-1 Specifications 11
- ‡fi ) ^& @ ! 0 9 8 6 5 1 17
- Light path 18
- Paper path 18
- 1-1-4 Drive system 19
- As viewed from machine rear 20
- 1-2-1 Drum 21
- 1-2-2 Developer and toner 21
- (1) Installation procedure 23
- Light source unit 1 pins 24
- Light source unit 2 pin 24
- Original detection switch 27
- Front cursor 28
- Rear cursor 28
- Drawer claw spacers 28
- Drawer spacers 28
- Fulcrum of the drawer lift 28
- Developing unit 30
- 12-pin connector 31
- Blue screws 31
- Waste toner tank 31
- Toner cartridge release lever 33
- 1-3-3 Copier management 36
- BVM4 × 6 screws 47
- BVM4 × 4 screw 47
- High temperature 47
- 2-pin receptacle 48
- 1-4-1 Maintenance mode 49
- U034 U066 U071 62
- Reference 64
- Description 65
- DF input light luminosity 65
- Setting range 65
- Initial setting 65
- 0 to 8 1 65
- 011 024 015 67
- 001 000 000 67
- 004 004 000 67
- (1) (2) (3) 70
- (4) (5) (6) 70
- (7) (8) (9) 70
- Toner sensor control voltage 74
- 0 to 255 155 74
- ≥ 1ST TEMP 77
- Maintenance cycle 85
- 0 to 600 100 1000 (copies) 85
- 0 to 200 (copies) 70 88
- U053 U065 U070 111
- Original Copy 112
- U034 U067 U072 113
- 1 2 3 122
- 4 5 6 122
- 7 8 9 122
- U402 U403 U404 143
- 1-5-1 Paper misfeed detection 152
- DFSW (ST) 1 154
- Paper size + 2000 ms 156
- DFSW (ST) 1* 157
- 5. Eject section 158
- 1-5-2 Self-diagnosis 163
- See page 1-5-22 168
- (13)Paper creases. Causes 173
- 1-5-4 Electrical problems 176
- 1-5-5 Mechanical problems 181
- Shaft handle retainer 184
- Paper feed cluth 184
- Cutout Stop ring 184
- Stop ring 185
- Upper paper feed pulleys 185
- Drawer drive motor 186
- Paper conveying unit 187
- Connector 187
- Lower left cover 187
- Bypass paper feed pulley 188
- Left registration roller 189
- Upper bypass cover 190
- (P. 1-6-36) 191
- (P. 1-4-14) 191
- • 15 cpm 192
- Figure 1-6-19b 192
- (P. 1-6-37) 194
- (P. 1-4-15) 194
- Figure 1-6-21b 195
- –1.5–1.5 196
- Figure 1-6-22b 199
- Right cover 200
- Contact glass 200
- Metal plate 200
- Scanner wire 201
- Scanner tension spring 201
- Scanner motor unit 202
- Frame securing tools 203
- Mirror 2 Frame 203
- Fan duct 205
- Laser scanner unit 205
- LSU front spacer 206
- LSU right spacer 206
- ISU cover 209
- Paper size switch 209
- Positioning pins 210
- Correct image 211
- Mirror 2 frame 212
- Figure 1-6-50b 216
- (P. 1-6-10) 217
- Scanner center line 218
- (P. 1-6-15) 219
- (P. 1-4-46) 219
- Image formation unit 221
- Drum shaft 224
- Drum drive grounding plate 224
- Doctor blade 225
- Adjustment screws 225
- Transfer roller assembly 226
- Cleaning blade 227
- M3 retainers 228
- Cleaning lower seal assembly 228
- 1-6-9 Fixing section 229
- Fixing unit thermister 230
- Heat roller separation claws 230
- Fixing heater 231
- Press springs 233
- Press roller 234
- 1-7-1 Replacing the main PCB 235
- Upper shield 237
- • Inverter PCB: VR1, VR2 240
- 2-1-1 Paper feed section 241
- Tungsten wire 244
- Main charger assembly 244
- Shield grid 244
- 2-1-3 Optical section 246
- 2-1-4 Developing section 250
- Cleaning spiral 257
- Lower cleaning seal 257
- Cleaning lamp (CL) 258
- Light-blocking lumirro 258
- 2-1-8 Fixing section 259
- 2-2-1 Electrical parts layout 261
- 2-3-2 Main PCB 269
- REV:2 270
- 2-3-3 CCD PCB 279
- 2-3-4 Laser diode PCB 280
- 2" × 8 283
- /2" × 8 286
- (20 cpm copier) 290
- Maintenance parts list 291
- • Copier 292
- • Optional drawer 294
Související produkty a manuály pro Kopírky Utax CD 1015
Kopírky Utax CD 1250 Specifikace
(240 stránky)
(240 stránky)
Kopírky Utax CD 1015 Uživatelský manuál
(56 stránky)
(56 stránky)
Kopírky Utax CD 1020 Uživatelský manuál
(72 stránky)
(72 stránky)
Kopírky Utax CD 1015 Servisní příručka
(241 stránky)
(241 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 1.131 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce