Utax CD 1015 Servisní příručka Strana 110
- Strana / 296
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Maintenance
Description
item No.
2AV/X
1-4-62
1-4
U060 Adjusting the scanner input properties
Description
Adjusts the image scanning density.
Purpose
Used when the entire image appears too dark or light.
Method
Press the start key.
Setting
1. Change the setting using the zoom +/– keys.
Description Setting range Initial setting
Image scanning density 0 to 23 12
Increasing the setting makes the density lower, and decreasing it makes the density higher.
2. Press the start key. The value is set.
Interrupt copy mode
While this maintenance item is being performed, copying from an original can be made in interrupt copy mode.
Completion
Press the stop/clear key at the screen for selecting an item. The indication for selecting a maintenance item No.
appears.
Caution
The following settings are also reset to the initial values by performing this maintenance item:
• Exposure density gradient set in maintenance mode (U093)
• Exposure set in the copy default item of the copier management mode
U061 Turning the exposure lamp on
Description
Turns the exposure lamp on.
Purpose
To check the exposure lamp.
Method
1. Press the start key. “on” appears.
2. Press the start key. The exposure lamp lights.
3. To turn the exposure lamp off, press the stop/clear key.
Completion
Press the stop/clear key. The indication for selecting a maintenance item No. appears.
U063 Adjusting the shading position
Description
Changes the shading position.
Purpose
Used when white lines continue to appear longitudinally on the image after the shading plate is cleaned. This is
due to flaws or stains inside the shading plate. To prevent this problem, the shading position should be changed
so that shading is possible without being affected by the flaws or stains.
Method
1. Press the start key.
2. Change the setting using the zoom +/– keys.
Description Setting range Initial setting Change in value per step
Shading position –5 to +5 0 0.17 mm
Increasing the setting moves the shading position toward the machine right, and decreasing it moves the
position toward the machine left.
3. Press the start key. The value is set.
Interrupt copy mode
While this maintenance item is being performed, copying from an original can be made in interrupt copy mode.
Completion
Press the stop/clear key at the screen for adjustment. The indication for selecting a maintenance item No.
appears.
- UTAX CD 1015 / 1020 1
- Double-pole/neutral fusing 2
- 1. Installation Precautions 4
- 3. Miscellaneous 6
- CONTENTS 7
- 1-6 Assembly and Disassembly 9
- 2-1 Mechanical construction 10
- 2-2 Electrical Parts Layout 10
- 2-3 Operation of the PCBs 10
- 2-4 Appendixes 10
- 1-1-1 Specifications 11
- ‡fi ) ^& @ ! 0 9 8 6 5 1 17
- Light path 18
- Paper path 18
- 1-1-4 Drive system 19
- As viewed from machine rear 20
- 1-2-1 Drum 21
- 1-2-2 Developer and toner 21
- (1) Installation procedure 23
- Light source unit 1 pins 24
- Light source unit 2 pin 24
- Original detection switch 27
- Front cursor 28
- Rear cursor 28
- Drawer claw spacers 28
- Drawer spacers 28
- Fulcrum of the drawer lift 28
- Developing unit 30
- 12-pin connector 31
- Blue screws 31
- Waste toner tank 31
- Toner cartridge release lever 33
- 1-3-3 Copier management 36
- BVM4 × 6 screws 47
- BVM4 × 4 screw 47
- High temperature 47
- 2-pin receptacle 48
- 1-4-1 Maintenance mode 49
- U034 U066 U071 62
- Reference 64
- Description 65
- DF input light luminosity 65
- Setting range 65
- Initial setting 65
- 0 to 8 1 65
- 011 024 015 67
- 001 000 000 67
- 004 004 000 67
- (1) (2) (3) 70
- (4) (5) (6) 70
- (7) (8) (9) 70
- Toner sensor control voltage 74
- 0 to 255 155 74
- ≥ 1ST TEMP 77
- Maintenance cycle 85
- 0 to 600 100 1000 (copies) 85
- 0 to 200 (copies) 70 88
- U053 U065 U070 111
- Original Copy 112
- U034 U067 U072 113
- 1 2 3 122
- 4 5 6 122
- 7 8 9 122
- U402 U403 U404 143
- 1-5-1 Paper misfeed detection 152
- DFSW (ST) 1 154
- Paper size + 2000 ms 156
- DFSW (ST) 1* 157
- 5. Eject section 158
- 1-5-2 Self-diagnosis 163
- See page 1-5-22 168
- (13)Paper creases. Causes 173
- 1-5-4 Electrical problems 176
- 1-5-5 Mechanical problems 181
- Shaft handle retainer 184
- Paper feed cluth 184
- Cutout Stop ring 184
- Stop ring 185
- Upper paper feed pulleys 185
- Drawer drive motor 186
- Paper conveying unit 187
- Connector 187
- Lower left cover 187
- Bypass paper feed pulley 188
- Left registration roller 189
- Upper bypass cover 190
- (P. 1-6-36) 191
- (P. 1-4-14) 191
- • 15 cpm 192
- Figure 1-6-19b 192
- (P. 1-6-37) 194
- (P. 1-4-15) 194
- Figure 1-6-21b 195
- –1.5–1.5 196
- Figure 1-6-22b 199
- Right cover 200
- Contact glass 200
- Metal plate 200
- Scanner wire 201
- Scanner tension spring 201
- Scanner motor unit 202
- Frame securing tools 203
- Mirror 2 Frame 203
- Fan duct 205
- Laser scanner unit 205
- LSU front spacer 206
- LSU right spacer 206
- ISU cover 209
- Paper size switch 209
- Positioning pins 210
- Correct image 211
- Mirror 2 frame 212
- Figure 1-6-50b 216
- (P. 1-6-10) 217
- Scanner center line 218
- (P. 1-6-15) 219
- (P. 1-4-46) 219
- Image formation unit 221
- Drum shaft 224
- Drum drive grounding plate 224
- Doctor blade 225
- Adjustment screws 225
- Transfer roller assembly 226
- Cleaning blade 227
- M3 retainers 228
- Cleaning lower seal assembly 228
- 1-6-9 Fixing section 229
- Fixing unit thermister 230
- Heat roller separation claws 230
- Fixing heater 231
- Press springs 233
- Press roller 234
- 1-7-1 Replacing the main PCB 235
- Upper shield 237
- • Inverter PCB: VR1, VR2 240
- 2-1-1 Paper feed section 241
- Tungsten wire 244
- Main charger assembly 244
- Shield grid 244
- 2-1-3 Optical section 246
- 2-1-4 Developing section 250
- Cleaning spiral 257
- Lower cleaning seal 257
- Cleaning lamp (CL) 258
- Light-blocking lumirro 258
- 2-1-8 Fixing section 259
- 2-2-1 Electrical parts layout 261
- 2-3-2 Main PCB 269
- REV:2 270
- 2-3-3 CCD PCB 279
- 2-3-4 Laser diode PCB 280
- 2" × 8 283
- /2" × 8 286
- (20 cpm copier) 290
- Maintenance parts list 291
- • Copier 292
- • Optional drawer 294
Související produkty a manuály pro Kopírky Utax CD 1015
Kopírky Utax CD 1250 Specifikace
(240 stránky)
(240 stránky)
Kopírky Utax CD 1015 Uživatelský manuál
(56 stránky)
(56 stránky)
Kopírky Utax CD 1020 Uživatelský manuál
(72 stránky)
(72 stránky)
Kopírky Utax CD 1015 Servisní příručka
(241 stránky)
(241 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.069 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce